Joined
·
29 Posts
FOLKS,
IF YOU CAN BUILD A MODEL CAR YOU CAN SAFLY PUT TOGETHER YOUR RIFLE AND BE PROUD OF IT.
YOU CAN SAVE hundreds OF DOLLARS AND THATS NOT A LIE!
THE ONLY TOOLS REQUIRED IS A CLEAR AREA TO WORK IN( YES A DINNING ROOM TABLE WILL BE FINE) A SMALL HAMMER A PUNCH SET,AND A PARTS BREAK DOWN AVAILABLE ANY WHERE ON THE WEB.
TO OBTAIN YOUR STRIPPED LOWER RECEIVER TRAVEL TO YOUR LOCAL GUNSHOW SOME DEALERS HAVE THEM ON HAND THEY RUN ANY WHERE FROM $90.00 TO $175.00 THIS IS YOUR LEGAL PART OF THE RIFLE, WITH THE S# ON IT SO THE STANDARD 4473 FORM PLUS BACK GROUND CHECK MUST BE DONE.
IF A SHOW IS TO FAR TO TRAVEL TO YOUR LOCAL GUNSHOP CAN ORDER ONE FOR YOU.
NOW ORDERING THE PART KIT I LIKE DEALING WITH "M&A PARTS INC" THERE KITS ARE PRE-BARRELED AND HEADSPACED THUS RELIEVEING YOU THE PURCHASE OF A BARREL NUT WRENCH, THERE LINK IS <WWW.M-APARTS.COM> .
ALSO THERE SERVICE IS FANTASTIC NOT ONLY WITH TURN AROUND TIME BUT SERVICE AFTER THE FACT AS WELL.
THE KITS RANGE FROM $425.00 FOR A STANDARD AR15 A-2 20"bbl OR 16" CAR STYLE TO $575.00 FOR A FULL BLOWN STAINLESS 24" BULL bbl VARMINT FLAT TOP, PLUS ANYTHING ELSE IN BETWEEN.
IN THE KIT YOU GET YOUR UPPER RECEIVER BARRELED AND READY TO FIRE. ALL PARTS REQUIRED FOR YOUR LOWER RECEIVER AGAIN VERY SIMPLE TO INSTALL ALL PARTS ARE DROP-IN AND NO FITTING IS REQUIRED, IS KITS ARE ALL TOP QUALITY NEW MIL-SPEC PARTS NOT TAKE-OFF`S OR REFRUB`S.
SO TO SOME IT UP! YOU CAN BUILD A STANDARD AR-15 A-2 FOR $425.00 FOR THE KIT AND SAY WE MEET IN THE MIDDLE $125.00 LOWER RECEIVER (THIS WAS A ARMALITE BRAND) DO THE MATH = $550.00 YOU WILL HAVE SOME LEG WORK ON YOUR PART TO DO PLUS YOUR S/H BUT CONSIDERING THAT LAW ENFORCEMENT DISCOUNTS THEY PAY $750 TO START I THINK IT IT WORTH YOUR TIME.
AM AS ONLY`S HERE TO HELP THE FELLOW SHOOTERS.
RON KONTOWSKY
ACTIONS BY R.A.K.
CUSTOM GUNSMITHING
p.s. CHECK WITH LOCAL LAW ON THE STYLEING YOU CAN OWN SINCE THE GUN BAN IS OVER YOU CAN OWN ANY SEMI-AUTO STYLE YOU WANT .
IF YOU CAN BUILD A MODEL CAR YOU CAN SAFLY PUT TOGETHER YOUR RIFLE AND BE PROUD OF IT.
YOU CAN SAVE hundreds OF DOLLARS AND THATS NOT A LIE!
THE ONLY TOOLS REQUIRED IS A CLEAR AREA TO WORK IN( YES A DINNING ROOM TABLE WILL BE FINE) A SMALL HAMMER A PUNCH SET,AND A PARTS BREAK DOWN AVAILABLE ANY WHERE ON THE WEB.
TO OBTAIN YOUR STRIPPED LOWER RECEIVER TRAVEL TO YOUR LOCAL GUNSHOW SOME DEALERS HAVE THEM ON HAND THEY RUN ANY WHERE FROM $90.00 TO $175.00 THIS IS YOUR LEGAL PART OF THE RIFLE, WITH THE S# ON IT SO THE STANDARD 4473 FORM PLUS BACK GROUND CHECK MUST BE DONE.
IF A SHOW IS TO FAR TO TRAVEL TO YOUR LOCAL GUNSHOP CAN ORDER ONE FOR YOU.
NOW ORDERING THE PART KIT I LIKE DEALING WITH "M&A PARTS INC" THERE KITS ARE PRE-BARRELED AND HEADSPACED THUS RELIEVEING YOU THE PURCHASE OF A BARREL NUT WRENCH, THERE LINK IS <WWW.M-APARTS.COM> .
ALSO THERE SERVICE IS FANTASTIC NOT ONLY WITH TURN AROUND TIME BUT SERVICE AFTER THE FACT AS WELL.
THE KITS RANGE FROM $425.00 FOR A STANDARD AR15 A-2 20"bbl OR 16" CAR STYLE TO $575.00 FOR A FULL BLOWN STAINLESS 24" BULL bbl VARMINT FLAT TOP, PLUS ANYTHING ELSE IN BETWEEN.
IN THE KIT YOU GET YOUR UPPER RECEIVER BARRELED AND READY TO FIRE. ALL PARTS REQUIRED FOR YOUR LOWER RECEIVER AGAIN VERY SIMPLE TO INSTALL ALL PARTS ARE DROP-IN AND NO FITTING IS REQUIRED, IS KITS ARE ALL TOP QUALITY NEW MIL-SPEC PARTS NOT TAKE-OFF`S OR REFRUB`S.
SO TO SOME IT UP! YOU CAN BUILD A STANDARD AR-15 A-2 FOR $425.00 FOR THE KIT AND SAY WE MEET IN THE MIDDLE $125.00 LOWER RECEIVER (THIS WAS A ARMALITE BRAND) DO THE MATH = $550.00 YOU WILL HAVE SOME LEG WORK ON YOUR PART TO DO PLUS YOUR S/H BUT CONSIDERING THAT LAW ENFORCEMENT DISCOUNTS THEY PAY $750 TO START I THINK IT IT WORTH YOUR TIME.
AM AS ONLY`S HERE TO HELP THE FELLOW SHOOTERS.
RON KONTOWSKY
ACTIONS BY R.A.K.
CUSTOM GUNSMITHING
p.s. CHECK WITH LOCAL LAW ON THE STYLEING YOU CAN OWN SINCE THE GUN BAN IS OVER YOU CAN OWN ANY SEMI-AUTO STYLE YOU WANT .
